Ressi TA 300
Ressi TA 300 is a premium tile adhesive formulated for high-strength tile fixing applications in demanding residential and commercial projects. The product offers reliable adhesion to concrete and cement-based surfaces while supporting efficient installation and long-term tile stability. Its advanced formulation contributes to improved workability and dependable bonding performance under varying environmental conditions. Ressi TA 300 is suitable for ceramic tiles, floor installations, wall applications, and general construction projects requiring durable tile bonding and professional finishing quality.
Ressi TA 300 is a specially designed tile adhesive for the applications at around freezing temperature i.e. cold storage or cold areas where temperature reaches to freezing. Ressi TA 300 is highly suitable for the bonding of most types of tiles. Ressi TA 300 is highly suitable for the application of porcelain, marble, granite, ceramic, glass tiles and many other different types of tiles in cold areas. Ressi TA 300 can easily be applied using the application spectrum as defined by BS EN 5385-1.
ADVANTAGES
- Crack resistant.
- Non-yellowing mortar.
- Dampness resistant.
- Fast Cure.
- Salt free mix
- Excellent workability.
- High bond strength.
- Slip resistant.
- Quick Set.
- Waterproof.
SURFACE PREPARATION
All loose particles and oil shall be cleaned off the surface prior to the application. Application on most type of cementitious surfaces like block work, concrete and rough plastered surfaces is possible. The surface should be sufficiently aged (At least 7 days for newly erected masonry surface and freshly plastered surface) before the installation of the tiling may begin. It is also recommended that expansion joints should not be tiled over, and suitable treatment should be done over them. Highly absorbent surfaces should be dampened, before spreading Ressi TA 300. Defective and unsound surfaces should be repaired before the installation of the tiles. It is also important to ensure that there is no dust at the backs of the tile, otherwise it may cause hollow sounds and improper adhesion of the tiles to the substrate.
PRODUCT PREPARATION
It is important that water is premeasured in accordance with the amount of material used. The Mortar powder should be added over the water to avoid the settlement of the material at the bottom of the mixing container. The Mixing container should be uncontaminated, non-corrosive and clean. Only potable water should be used for mixing. It is also recommended that the material should be mechanically mixed with a mortar mixer or other mechanical mixing methods to obtain a consistent lump free mix.
APPLICATION
Buttering of the material onto the back of the tiles is usually not recommended as it this may cause poor adhesion. Spread the material evenly onto the surface using a suitable straight edge trowel and then notch immediately. To ensure good bonding, it is recommended not to spread the material more than 1m2 at a time as the mortar may dry up resulting in poor adhesion and causing difficulties in application. After the application and levelling of the mortar, the tiles should be firmly knocked into the position. Adjustment of the tiles should be done at a maximum of 10 minutes after application.
TECHNICAL TABLE
| Property |
Result |
| Appearance |
White powder |
| Composition |
Contains cement and selected aggregates along with additives to improve consistency, workability, and durability. |
| Maximum aggregate size |
0.6mm |
| *Water application |
14% ± 2% |
| *Pull off strength |
1.0 N / mm² @ 28 Days (Tested as per BS EN 12004-2) |
| *Slip test |
Non-Slip as per BS EN 12004-2 |
| *Open time |
10 Min Tested as per BS EN 12004-2 |
| *Water Retention |
99.6% |
| *Application yield / Coverage |
0.78m³ / T |
*Typical results under laboratory conditions.
Complies with BS EN 12004-1 Type C Class 2FT
SHELF LIFE
Expiration of Ressi TA 300 is at 12 months after production date under dry and sheltered conditions.
PACKAGING
Ressi TA 300 is supplied in 20 KG bags.
HEALTH & SAFETY
Ressi TA 300 is regarded as non-hazardous for transportation. Do not reuse bags or containers and dispose them off as per local rules and regulations. Gloves and suitable masks can be worn during application. Please refer to the MSDS of the product for further health and safety information.
