Zepoxy Epo Iron Primer by ressichem

Zepoxy Epo Iron Primer

Zepoxy Epo Iron Primer is a Red-Oxide and Zinc-based epoxy primer designed for Iron-based substrates for subsequent protection from rusting. It has a high adhesive, mechanical and abrasivestrength which ensures its corrosion protection properties even in rough and tough use conditions

Clear
Add to wishlist
Category

    Zepoxy Epo Iron Primer is a Red-Oxide and Zinc-based epoxy primer designed for Iron-based substrates for subsequent protection from rusting. It has a high adhesive, mechanical and abrasive strength which ensures its corrosion protection properties even in rough and tough use conditions

    TECHNICAL DATA

    Property 

    Test Method

    Result

    Appearance Part A

    Visual

    Low viscosity, red liquid

    Appearance Part B

    Visual

    Low viscosity, yellow to brown liquid

    Mix ratio (Part A : Part B)

    Theoretical

    100 : 16

    Mix viscosity @ 25°C

    ASTM D 2196

    250 – 500 cPs

    Solid Content

    –

    65 – 67 %

    Flash Point

    ASTM D 93

    >14°C

    Pot life (300g mix) @ 30°C

    –

    >1 hour

    Coverage per kg material

    –

    80sq.ft, 30-50 microns thickness

    Hardening time

    –

    24 hours

    Full Cure

    –

    7 days

    Note: • At 40°C pot life will halve so application should be planned accordingly

    GENERAL INFORMATION

    SUBSTRATE PREPARATION

    The surface of the substrate must be clean and dry. Remove all dirt, grease and foreign material by cleaning with suitable solvent, sand blasting, mechanical abrasion, or acid etching.

    MIXING

    In order to obtain good results, resin should be pre-mixed and then the hardener should be added. Thorough mixing of the ingredients is essential. Usually the resin and hardener are mixed in small quantities to extend the working time and prevent high exothermic reaction and pre-gelling.

    APPLICATION

    To ensure good adhesion between the substrates, it is recommended to apply rich layer of homoge nous blend uniformly on the surface and fifill the dents and pinholes. Adequate cuing normally takes place within 24 hours, post curing at temperatures more than 40°C is recommended.

    CLEANING AND MAINTENANCE OF EQUIPMENT

    Tools and equipment used during the process are best cleaned immediately after use since removal of cured resin is diffificult and time consuming. It is recommended that the bulk of the resin be removed using a scrapper and the remainder washed away using solvents such as toluene, xylene or acetone.

    PACKAGING

    Zepoxy Epo Iron Primer is available as follows:

    • 11.6 KG Set

    HEALTH AND SAFETY

    Please dispose off containers of the materials as per local laws, rules and regulations. Usage of gloves, safety masks and other safety apparel as per health and safety laws should be done. Especially wear a respirator when sanding cured resin, and if you use alcohol inks DO NOT use a flame to remove bubbles, as alcohol is flammable. For further assistance, please refer to the MSDS of the product for further health and safety information.

    Packaging

    11.6 KG
Technical Datasheet
Product Description

Zepoxy Epo Iron Primer is a Red-Oxide and Zinc-based epoxy primer designed for Iron-based substrates for subsequent protection from rusting. It has a high adhesive, mechanical and abrasive strength which ensures its corrosion protection properties even in rough and tough use conditions

Zepoxy Epo Iron Primer is a Red-Oxide and Zinc-based epoxy primer designed for Iron-based substrates for subsequent protection from rusting. It has a high adhesive, mechanical and abrasive strength which ensures its corrosion protection properties even in rough and tough use conditions

TECHNICAL DATA

Property 

Test Method

Result

Appearance Part A

Visual

Low viscosity, red liquid

Appearance Part B

Visual

Low viscosity, yellow to brown liquid

Mix ratio (Part A : Part B)

Theoretical

100 : 16

Mix viscosity @ 25°C

ASTM D 2196

250 – 500 cPs

Solid Content

-

65 – 67 %

Flash Point

ASTM D 93

>14°C

Pot life (300g mix) @ 30°C

-

>1 hour

Coverage per kg material

-

80sq.ft, 30-50 microns thickness

Hardening time

-

24 hours

Full Cure

-

7 days

Note: • At 40°C pot life will halve so application should be planned accordingly

GENERAL INFORMATION

SUBSTRATE PREPARATION

The surface of the substrate must be clean and dry. Remove all dirt, grease and foreign material by cleaning with suitable solvent, sand blasting, mechanical abrasion, or acid etching.

MIXING

In order to obtain good results, resin should be pre-mixed and then the hardener should be added. Thorough mixing of the ingredients is essential. Usually the resin and hardener are mixed in small quantities to extend the working time and prevent high exothermic reaction and pre-gelling.

APPLICATION

To ensure good adhesion between the substrates, it is recommended to apply rich layer of homoge nous blend uniformly on the surface and fifill the dents and pinholes. Adequate cuing normally takes place within 24 hours, post curing at temperatures more than 40°C is recommended.

CLEANING AND MAINTENANCE OF EQUIPMENT

Tools and equipment used during the process are best cleaned immediately after use since removal of cured resin is diffificult and time consuming. It is recommended that the bulk of the resin be removed using a scrapper and the remainder washed away using solvents such as toluene, xylene or acetone.

PACKAGING

Zepoxy Epo Iron Primer is available as follows:

  • 11.6 KG Set

HEALTH AND SAFETY

Please dispose off containers of the materials as per local laws, rules and regulations. Usage of gloves, safety masks and other safety apparel as per health and safety laws should be done. Especially wear a respirator when sanding cured resin, and if you use alcohol inks DO NOT use a flame to remove bubbles, as alcohol is flammable. For further assistance, please refer to the MSDS of the product for further health and safety information.