Ressi SLS 610

Ressi SLS 610 is ready to use premixed self-leveling floor screed which is suitable for both old and new, internal, and external floorings where light to mild traffic is expected. The application thickness of Ressi SLS 610 is between 4mm to 8mm. Ressi SLS 610 is ideal for use to level substrates prior to laying carpets, floor tiles etc. Ressi SLS 610 is also an ideal substrate for the waterproofing of roofs where further coatings can be applied on the surface. Ressi SLS is also ideal for Epoxy Flooring applications where a smooth cementitious floor is required prior to the application of a proper epoxy flooring system.

ADVANTAGES

• Good weather resistance.
• High durability.
• Easy to use by simply adding water.
• Premixed material to ensure good consistent quality and mix.
• Promotes cleaner and safer sites.

SURFACE PREPARATION

The quality of the existing floor is the deciding factor of the strength of Ressi SLS 610. The floor should be solid, free of dust, grease, and loose material. If the surface is covered with a cement film or has weak parts, these will be needed to be removed by shot blasting, diamond grinding or similar. Loose material is best removed with a vacuum cleaner, where grease etc. on concrete, painted surfaces, old tiles and similar is to be cleaned with a suitable cleaning agent.

PRODUCT PREPARATION

For Manual application, Mix Ressi SLS 610 in a clean bucket with the correct amount of water. The material is mixed for 1-2 minutes until it is of smooth and even consistency. The mortar powder should be added over the water to avoid the settlement of the material at the bottom of the mixing container. The mixing container should be uncontaminated, non-corrosive and clean. For larger areas and speedy application is recommended to use a continuous mixer and pouring mechanism to achieve best and consistent results. Only potable water should be used for mixing. It is also recommended that material should be mechanically mixed with a mortar mixer or other mechanical mixing methods to obtain a consistent lump free mix.

APPLICATION

Ressi SLS 610 is applied on the floor across the width of the area. Use a notched trowel for an even distribution of the material into the corners. If a thin layer is to be obtained, a notched trowel can also be used for that. For the application of large surfaces, it is highly recommended to use a mixer/pump for the application of Ressi SLS 610. If a colored finished floor is required in one go, Ressi Hardener (color hardener) can be sprinkled over the surface using a dry shake sprinkle method and then finished with suitable finishing tools.

SURFACE TREATMENT

When Ressi SLS 610 is applied and the instructed drying times followed - the laid flooring can be covered with a variety of flooring products e.g., carpet, vinyl, ceramic tiles, flooring epoxy, various waterproofing coatings etc.

PRIMING

Once the flooring of Ressi SLS 610 has been laid and proper strength of the material is achieved after 28 days a variety of subsequent treatments can be done over it. All primers which are cement compatible can be applied over the prepared surface of Ressi SLS 610. Incase an epoxy flooring system is applied, Ressi EPO Primer is a suitable primer which is recommended.

CURING

No curing required in general, however maximum curing for 72 hours where hot climatic conditions prevail.

SHELF LIFE

Expiration of Ressi SLS 610 is at 6 months after production date under dry and sheltered conditions.

TECHNICAL DATA

_{*Typical results under laboratory conditions}

PACKAGING

Ressi SLS 610 is available in 20 KG and 50 KG bags.

NOTE:

If printed bags are not available, neutral bags with label. Lot number and manufacturing date to be stamped at the back of each bag.

HEALTH AND SAFETY

Ressi SLS 610 is regarded as non-hazardous for transportation. Do not reuse bags or containers & dispose them off as per local rules and regulations. Gloves and suitable masks can be worn during application. Please refer to the product MSDS for further health and safety information.