Insulaster

Insulaster is a ready to use floor screed and plaster material designed to provide insulation and a lightweight screed solution for sunk areas where a lot of weight cannot be placed over the concrete slab. Insulaster Provides thermal fire and acoustic insulation together. Insulaster can be applied to both interior and exterior surfaces of old and new buildings allowing them to breathe.

Clear
Add to wishlist

    Insulaster is a ready to use floor screed and plaster material designed to provide insulation and a lightweight screed solution for sunk areas where a lot of weight cannot be placed over the concrete slab. It Provides thermal fire and acoustic insulation together. Insulaster can be applied to both interior and exterior surfaces of old and new buildings allowing them to breathe. Insulaster is ideal for the following places:

    • Commercial buildings.
    • Residential buildings.
    • Public buildings.
    • Industrial buildings.
    • Institutional buildings.
    • Fire escape zones and equipment rooms

    ADVANTAGES 

    • Long lasting.
    • Easy application.
    • Protection from thermal shocks.
    • Saves energy.
    • Natural and harmless to environment.
    • Ready to use.
    • Fire Resistant (Fire Resistance property Mentioned in technical Table)
    • Provides superior sound proofing.
    • Does not allow heat transfer thus not affected by hot or cold temperatures.
    • Allows the building to breath naturally.
    • Does not have emission of greenhouse gases.

    SURFACE PREPARATION

    For hot climatic conditions, the surface may be dampened with potable water. All loose particles and oil shall be cleaned off the surface prior to application. It is recommended to have a proper cementitious waterproofing system implemented over a new RCC surface to make it watertight (For Example: Water Guard 491 From Ressichem).

    Note: Over RCC and smooth concrete surfaces, a base coat of Ressi BRC 7000 may be used if required.

    PRODUCT PREPARATION 

    Since Insulaster can be applied both as a floor screed and a plaster, the water demands for both the applications will vary. Depending on the ambient temperature of the applications, the water demand may also be adjusted to accommodate working times of the materials. Please refer to the mixing ratios in the technical table. it is recommended to prepare an onsite trial to determine the optimum water ratio for the application requirement. The mortar powder and light weight aggregate should be added over the water to avoid settlement of the material at the bottom of the mixing container. The mixing container should be uncontaminated, non-corrosive and clean using only potable water. It is recommended to use an automatic drill machine mixer for the mixing of Insulaster with water.

    APPLICATION

    With Proper surface preparation, conventional plastering and screeding techniques can be used for its application. It is essential to have proper levelling dabs to determine the thickness of the materials both on walls and the floor surface. The ideal surface for the application of Insulaster is RCC Surface and it is recommended to have a prepared masonry or concrete surface ready to plaster for the application of Insulaster. All loose particles such as oil grease and any other particles that may cause bonding issues need to be cleaned off the surface prior to the application of Insulaster. It is also recommended to dampen the surface if the ambient temperature is exceeding 35°C and the application surface feels heated.

    CURING

    No curing required in General, however if temperatures exceed 35°C it is recommended to mist cure for 3 days once the material has initially hardened after 48 Hours.

    SHELF LIFE

    Expiration of Insulaster is 12 Months after production under dry and sheltered conditions. High levels of humidity and moisture may reduce shelf life.

    HEALTH AND SAFETY

    Insulaster is regarded as non-hazardous for transportation. Do not re use bags and containers and dispose them off as per local rules and regulations. Gloves and suitable masks can be worn during
    application.

    TECHNICAL  DATA

    Property Test Method and / or compliance standard Test Method and / or compliance standard
    *DRY DENSITY BS EN 1015-10 600 ± 100 kg/m³
    *THERMAL CONDUCTIVITY PCSIR Lab developed Method < 0.03 W/m.k
    *COMPRESSION
    STRENGTH
    BSEN 998-1 & BSEN 1015-11 CS I
    *BOND STRENGTH BSEN 998-1 & BSEN 1015-12 0.1 N/mm²
    *WATER ABSORPTION BSEN 1015-19 & BSEN 1015-18 (W2) (<0.2Kg/m² min½)
    *FIRE ENDURANCE PCSIR Lab developed Method 538 C for 5min : 14.6%
    APPLICATION WATER BSEN 1015-3 704 C for 10min : 6.5%
    *READINESS FOR PAINTING Internal Lab developed Method by
    Manufacturer @ 24°C
    Drying time 72 hours at
    appropriate environment
    *RETENTION PERIOD Internal Lab developed Method by
    Manufacturer
    06 months at appropriate environment
    APPLICATION TYPE Internal Lab developed Method by
    Manufacturer
    Hand Application
    *WATER APPLICATION I Internal Lab developed Method by
    Manufacturer
    36% ±10%

    *Typical results under laboratory conditions.

    SPECIAL  NOTE

    Before the application of any product like wall putty, paint, wallpaper, decorative plaster, or any other coating, Insulaster must be dried out completely with no moisture content inside of it.

    PACKAGING

    Insulaster is available in two parts:
    Part A      50 KG Powdered Bag
    Part B      802g Lightweight high-volume flame-retardant filler (EPS beads).

     

     

     

     

     

     

     

     

     

    NOTE

    If printed bags are not available, neutral bags with label. Lot number and manufacturing date to be stamped at the back of each bag.

    Packaging

    802 KG, 50 KG


Product Description

Insulaster is a ready to use floor screed and plaster material designed to provide insulation and a lightweight screed solution for sunk areas where a lot of weight cannot be placed over the concrete slab. It Provides thermal fire and acoustic insulation together. Insulaster can be applied to both interior and exterior surfaces of old and new buildings allowing them to breathe. Insulaster is ideal for the following places:

Insulaster is a ready to use floor screed and plaster material designed to provide insulation and a lightweight screed solution for sunk areas where a lot of weight cannot be placed over the concrete slab. It Provides thermal fire and acoustic insulation together. Insulaster can be applied to both interior and exterior surfaces of old and new buildings allowing them to breathe. Insulaster is ideal for the following places:

  • Commercial buildings.
  • Residential buildings.
  • Public buildings.
  • Industrial buildings.
  • Institutional buildings.
  • Fire escape zones and equipment rooms

ADVANTAGES 

  • Long lasting.
  • Easy application.
  • Protection from thermal shocks.
  • Saves energy.
  • Natural and harmless to environment.
  • Ready to use.
  • Fire Resistant (Fire Resistance property Mentioned in technical Table)
  • Provides superior sound proofing.
  • Does not allow heat transfer thus not affected by hot or cold temperatures.
  • Allows the building to breath naturally.
  • Does not have emission of greenhouse gases.

SURFACE PREPARATION

For hot climatic conditions, the surface may be dampened with potable water. All loose particles and oil shall be cleaned off the surface prior to application. It is recommended to have a proper cementitious waterproofing system implemented over a new RCC surface to make it watertight (For Example: Water Guard 491 From Ressichem).

Note: Over RCC and smooth concrete surfaces, a base coat of Ressi BRC 7000 may be used if required.

PRODUCT PREPARATION 

Since Insulaster can be applied both as a floor screed and a plaster, the water demands for both the applications will vary. Depending on the ambient temperature of the applications, the water demand may also be adjusted to accommodate working times of the materials. Please refer to the mixing ratios in the technical table. it is recommended to prepare an onsite trial to determine the optimum water ratio for the application requirement. The mortar powder and light weight aggregate should be added over the water to avoid settlement of the material at the bottom of the mixing container. The mixing container should be uncontaminated, non-corrosive and clean using only potable water. It is recommended to use an automatic drill machine mixer for the mixing of Insulaster with water.

APPLICATION

With Proper surface preparation, conventional plastering and screeding techniques can be used for its application. It is essential to have proper levelling dabs to determine the thickness of the materials both on walls and the floor surface. The ideal surface for the application of Insulaster is RCC Surface and it is recommended to have a prepared masonry or concrete surface ready to plaster for the application of Insulaster. All loose particles such as oil grease and any other particles that may cause bonding issues need to be cleaned off the surface prior to the application of Insulaster. It is also recommended to dampen the surface if the ambient temperature is exceeding 35°C and the application surface feels heated.

CURING

No curing required in General, however if temperatures exceed 35°C it is recommended to mist cure for 3 days once the material has initially hardened after 48 Hours.

SHELF LIFE

Expiration of Insulaster is 12 Months after production under dry and sheltered conditions. High levels of humidity and moisture may reduce shelf life.

HEALTH AND SAFETY

Insulaster is regarded as non-hazardous for transportation. Do not re use bags and containers and dispose them off as per local rules and regulations. Gloves and suitable masks can be worn during
application.

TECHNICAL  DATA

Property Test Method and / or compliance standard Test Method and / or compliance standard
*DRY DENSITY BS EN 1015-10 600 ± 100 kg/m³
*THERMAL CONDUCTIVITY PCSIR Lab developed Method < 0.03 W/m.k
*COMPRESSION
STRENGTH
BSEN 998-1 & BSEN 1015-11 CS I
*BOND STRENGTH BSEN 998-1 & BSEN 1015-12 0.1 N/mm²
*WATER ABSORPTION BSEN 1015-19 & BSEN 1015-18 (W2) (<0.2Kg/m² min½)
*FIRE ENDURANCE PCSIR Lab developed Method 538 C for 5min : 14.6%
APPLICATION WATER BSEN 1015-3 704 C for 10min : 6.5%
*READINESS FOR PAINTING Internal Lab developed Method by
Manufacturer @ 24°C
Drying time 72 hours at
appropriate environment
*RETENTION PERIOD Internal Lab developed Method by
Manufacturer
06 months at appropriate environment
APPLICATION TYPE Internal Lab developed Method by
Manufacturer
Hand Application
*WATER APPLICATION I Internal Lab developed Method by
Manufacturer
36% ±10%

*Typical results under laboratory conditions.

SPECIAL  NOTE

Before the application of any product like wall putty, paint, wallpaper, decorative plaster, or any other coating, Insulaster must be dried out completely with no moisture content inside of it.

PACKAGING

Insulaster is available in two parts:
Part A      50 KG Powdered Bag
Part B      802g Lightweight high-volume flame-retardant filler (EPS beads).

 

 

 

 

 

 

 

 

 

NOTE

If printed bags are not available, neutral bags with label. Lot number and manufacturing date to be stamped at the back of each bag.