Paint Guard 10,000 C
Paint Guard 10000 C is a protective coating solution designed to enhance surface durability and improve resistance against environmental exposure, abrasion, and surface wear. The product provides reliable adhesion and long-lasting coating performance while supporting improved surface appearance and protection in commercial and industrial applications. Its advanced formulation contributes to durable finishing results and dependable maintenance performance under demanding operating conditions. Paint Guard 10000 C is suitable for walls, industrial surfaces, decorative coatings, and protective finishing applications requiring reliable surface durability.
Paint Guard 10,000 C is cement based waterproof thin applied plaster which is ideal for use on concrete / Plastered walls and ceilings. It fills fine pores of plaster and concrete and provides a smooth and dry surface essential for painting. Paint Guard 10,000 C is an ideal putty to be used in combination with Ressi PlastoRend 120, Insulaster or any other plaster material by Ressichem Prior to finishing it for paint. Paint Guard 10,000 C is suitable for many mineral based backgrounds and plasters as well prior to the application of paint and wallpaper.
ADVANTAGES
- Better adhesion and durability compared to other putties.
- Applicable on both internal and external surface.
- No curing required.
- Water resistant, application on moist surfaces possible (2 Coat application).
- Smooth Finish.
- Any type of paint or distemper can be applied on Paint Guard 10,000 C.
- No primer required prior to application.
- Helps in preventing the growth of algae and fungus on walls.
- Premixed material; just add water.
SURFACE PREPARATION
Remove all loose particles, dust, oil, grease, and any other material which may result in poor adhesion from the substrate. The surface required for the application of Paint Guard 10,000 C is usually a concrete levelled surface or a levelled plastered surface.
PRODUCT PREPARATION
it is important that water is premeasured in accordance with the amount of material used. Paint Guard 10,000 C should be added over the water to avoid the settlement of the material at the bottom of the mixing container. The mixing container should be uncontaminated, non-corrosive and clean. Only potable water should be used for mixing.
APPLICATION
Paint Guard 10,000 C is applied onto the prepared surface using a painters knife, Steel trowel or appropriate tools used to achieve the desired thickness and finish of the product. Paint Guard 10,000 C is not a brush applied material. It is recommended to build up the thickness of the putty layer by layer. The total thickness of one coat should be limited to no more than 2mm. Multiple coats can be applied.
TECHNICAL DATA
|
Appearance
|
Grey, White or Colored Powder
|
|
Composition
|
Contains cement and selected aggregates along with additives to improve consistency, workability, and durability
|
|
*Maximum Aggregate Size
|
0.3 mm
|
|
*Water application
|
40% ± 5%
|
|
*Wet Mix Life
|
Approximately 30 Mins @ 20°C (Tested as per BS EN 1015-9)
|
|
*Compressive Strength
|
10.00 N / mm2 @ 28 Days (Tested as per BS EN 1015-11)
|
|
*Flexural Strength
|
3.00 N / mm2 @ 28 Days (tested as per BS EN 1015-12)
|
|
*Approximate Yield / Coverage
|
0.85 m3 / T
|
*Typical Results under laboratory conditions.
CURING
No curing required in general, however if temperature during application exceed 40°C, curing for 48 Hours is recommended.
SHELF LIFE
Expiration of Paint Guard 10,000 C is at 6 months after production date under dry and sheltered conditions.
PACKAGING
Paint Guard 10,000 C is available in 1 KG, 12 KG and 15 KG Packs
HEALTH AND SAFETY
Paint Guard 10,000 C is regarded as non-hazardous for transportation. Do not reuse bags or containers and dispose them off as per local rules and regulations. Gloves and suitable masks can be worn during application. Please refer to the MSDS of the product for further health and safety information.
NOTE:
If printed packaging not available, neutral packaging with label. Lot number and manufacturing date to be stamped at the back of each packaging.
