Zepoxy 700

Zepoxy 700 is a low gloss epoxy system for general purpose coatings and thin castings. This system offers a moderate open time, medium viscosity, good wetting characteristics, excellent adhesion, and excellent mechanical strength.

Clear
Add to wishlist
Category

    Zepoxy 700 is a low gloss epoxy system for general purpose coatings and thin castings. This system offers a moderate open time, medium viscosity, good wetting characteristics, excellent adhesion, and excellent mechanical strength.

    TECHNICAL DATA

    Property Test Method Result
    Appearance Part A Visual Medium viscosity, clear to light yellow liquid
    Appearance Part B Visual Low viscosity, yellow liquid
    Mix ratio (Part A: Part B) Theoretical 100: 50
    *Mix viscosity @ 25°C ASTM D 2196 1000 – 5000 cPs
    *Flash Point ASTM D 93 >135°C
    Coverage per KG Theoretical 9 SFT @ 1mm thick
    Recommended maximum casting thickness 5mm
    *Pot life (300g mix) @ 30°C 45 min
    *Hardening time 24 hours
    *Full Cure 7 days
    *Flexural Strength (MPa) ASTM D 790 100.0
    *Compressive Strength (MPa) ASTM D 695 85.0
         

    These are typical results under laboratory conditions.

    NOTE

    At 40°C gel time will be reduced to half, in case of increased temperatures, pouring should be planned accordingly.

    MIXING

    The mixing ratio must be accurately followed to achieve perfect results. It is not possible to change the ratio which would result in the epoxy not drying properly and lower mechanical properties. Pour the hardener first and then the resin. The mixed components should be thoroughly mixed for 3-4 minutes to ensure an even consistency. To avoid development of bubbles slowly mix for 5-10 mins. Once the epoxy is mixed and poured gently pass warm air from a heat gun or hair dryer on slowest speed setting, this will assist in removal of any bubbles generated during mixing.

    PAKAGING

    1.5 KG Sets               Part A 1 KG
                                     Part B 500g

    15 KG Sets                Part A 10 KG
                                     Part B 5 KG

    45 KG Sets                Part A 30 KG
                                     Part B 15 KG

    HEALTH AND SAFETY

    Dispose containers of the materials as per local laws, rules, and regulations. Use gloves, safety masks and other safety apparel as per health and safety laws. For further assistance, please refer to the MSDS of the product for further health and safety information.

    Packaging

    1.5 KG, 15 KG, 45 KG


Product Description

Zepoxy 700 is a low gloss epoxy system for general purpose coatings and thin castings. This system offers a moderate open time, medium viscosity, good wetting characteristics, excellent adhesion, and excellent mechanical strength.

Zepoxy 700 is a low gloss epoxy system for general purpose coatings and thin castings. This system offers a moderate open time, medium viscosity, good wetting characteristics, excellent adhesion, and excellent mechanical strength.

TECHNICAL DATA

Property Test Method Result
Appearance Part A Visual Medium viscosity, clear to light yellow liquid
Appearance Part B Visual Low viscosity, yellow liquid
Mix ratio (Part A: Part B) Theoretical 100: 50
*Mix viscosity @ 25°C ASTM D 2196 1000 – 5000 cPs
*Flash Point ASTM D 93 >135°C
Coverage per KG Theoretical 9 SFT @ 1mm thick
Recommended maximum casting thickness - 5mm
*Pot life (300g mix) @ 30°C - 45 min
*Hardening time - 24 hours
*Full Cure - 7 days
*Flexural Strength (MPa) ASTM D 790 100.0
*Compressive Strength (MPa) ASTM D 695 85.0
     

These are typical results under laboratory conditions.

NOTE

At 40°C gel time will be reduced to half, in case of increased temperatures, pouring should be planned accordingly.

MIXING

The mixing ratio must be accurately followed to achieve perfect results. It is not possible to change the ratio which would result in the epoxy not drying properly and lower mechanical properties. Pour the hardener first and then the resin. The mixed components should be thoroughly mixed for 3-4 minutes to ensure an even consistency. To avoid development of bubbles slowly mix for 5-10 mins. Once the epoxy is mixed and poured gently pass warm air from a heat gun or hair dryer on slowest speed setting, this will assist in removal of any bubbles generated during mixing.

PAKAGING

1.5 KG Sets               Part A 1 KG
                                 Part B 500g

15 KG Sets                Part A 10 KG
                                 Part B 5 KG

45 KG Sets                Part A 30 KG
                                 Part B 15 KG

HEALTH AND SAFETY

Dispose containers of the materials as per local laws, rules, and regulations. Use gloves, safety masks and other safety apparel as per health and safety laws. For further assistance, please refer to the MSDS of the product for further health and safety information.