Zepoxy 700

Zepoxy 700 is a low gloss epoxy system for general purpose coatings and thin castings. This system offers a moderate open time, medium viscosity, good wetting characteristics, excellent adhesion, and excellent mechanical strength.

Clear
Add to wishlist

    Zepoxy 700 is a low gloss epoxy system for general purpose coatings and thin castings. This system offers a moderate open time, medium viscosity, good wetting characteristics, excellent adhesion, and excellent mechanical strength.

    TECHNICAL DATA

    PropertyTest MethodResult
    Appearance Part AVisualMedium viscosity, clear to light yellow liquid
    Appearance Part BVisualLow viscosity, yellow liquid
    Mix ratio (Part A: Part B)Theoretical100: 50
    *Mix viscosity @ 25°CASTM D 21961000 – 5000 cPs
    *Flash PointASTM D 93>135°C
    Coverage per KGTheoretical9 SFT @ 1mm thick
    Recommended maximum casting thickness5mm
    *Pot life (300g mix) @ 30°C45 min
    *Hardening time24 hours
    *Full Cure7 days
    *Flexural Strength (MPa)ASTM D 790100.0
    *Compressive Strength (MPa)ASTM D 69585.0
       

    These are typical results under laboratory conditions.

    NOTE

    At 40°C gel time will be reduced to half, in case of increased temperatures, pouring should be planned accordingly.

    MIXING

    The mixing ratio must be accurately followed to achieve perfect results. It is not possible to change the ratio which would result in the epoxy not drying properly and lower mechanical properties. Pour the hardener first and then the resin. The mixed components should be thoroughly mixed for 3-4 minutes to ensure an even consistency. To avoid development of bubbles slowly mix for 5-10 mins. Once the epoxy is mixed and poured gently pass warm air from a heat gun or hair dryer on slowest speed setting, this will assist in removal of any bubbles generated during mixing.

    PAKAGING

    1.5 KG Sets               Part A 1 KG
                                     Part B 500g

    15 KG Sets                Part A 10 KG
                                     Part B 5 KG

    45 KG Sets                Part A 30 KG
                                     Part B 15 KG

    HEALTH AND SAFETY

    Dispose containers of the materials as per local laws, rules, and regulations. Use gloves, safety masks and other safety apparel as per health and safety laws. For further assistance, please refer to the MSDS of the product for further health and safety information.

    Packaging

    1.5 KG, 15 KG, 45 KG


Product Description

Zepoxy 700 is a low gloss epoxy system for general purpose coatings and thin castings. This system offers a moderate open time, medium viscosity, good wetting characteristics, excellent adhesion, and excellent mechanical strength.

Zepoxy 700 is a low gloss epoxy system for general purpose coatings and thin castings. This system offers a moderate open time, medium viscosity, good wetting characteristics, excellent adhesion, and excellent mechanical strength.

TECHNICAL DATA

PropertyTest MethodResult
Appearance Part AVisualMedium viscosity, clear to light yellow liquid
Appearance Part BVisualLow viscosity, yellow liquid
Mix ratio (Part A: Part B)Theoretical100: 50
*Mix viscosity @ 25°CASTM D 21961000 – 5000 cPs
*Flash PointASTM D 93>135°C
Coverage per KGTheoretical9 SFT @ 1mm thick
Recommended maximum casting thickness-5mm
*Pot life (300g mix) @ 30°C-45 min
*Hardening time-24 hours
*Full Cure-7 days
*Flexural Strength (MPa)ASTM D 790100.0
*Compressive Strength (MPa)ASTM D 69585.0
   

These are typical results under laboratory conditions.

NOTE

At 40°C gel time will be reduced to half, in case of increased temperatures, pouring should be planned accordingly.

MIXING

The mixing ratio must be accurately followed to achieve perfect results. It is not possible to change the ratio which would result in the epoxy not drying properly and lower mechanical properties. Pour the hardener first and then the resin. The mixed components should be thoroughly mixed for 3-4 minutes to ensure an even consistency. To avoid development of bubbles slowly mix for 5-10 mins. Once the epoxy is mixed and poured gently pass warm air from a heat gun or hair dryer on slowest speed setting, this will assist in removal of any bubbles generated during mixing.

PAKAGING

1.5 KG Sets               Part A 1 KG
                                 Part B 500g

15 KG Sets                Part A 10 KG
                                 Part B 5 KG

45 KG Sets                Part A 30 KG
                                 Part B 15 KG

HEALTH AND SAFETY

Dispose containers of the materials as per local laws, rules, and regulations. Use gloves, safety masks and other safety apparel as per health and safety laws. For further assistance, please refer to the MSDS of the product for further health and safety information.