Zepoxy 200

Zepoxy 200 is an all-purpose epoxy adhesive useful for bonding of materials such as metal, wood, ceramic, FRP, concrete, textile, glass, leather, etc. It has higher bonding power as well as higher mechanical strength making this system a higher performance version of Zepoxy 100.

Clear
Add to wishlist
Category

    Zepoxy 200 is an all-purpose epoxy adhesive useful for bonding of materials such as metal, wood, ceramic, FRP, concrete, textile, glass, leather, etc. It has higher bonding power as well as higher mechanical strength making this system a higher performance version of Zepoxy 100.

    TECHNICAL DATA

    Property Test Method Result
    Appearance Part A Visual High viscosity, translucent liquid
    Appearance Part B Visual High viscosity, yellow to brown liquid
    Mix ratio (Part A: Part B) Theoretical 100: 80
    *Mix viscosity @ 25°C ASTM D 2196 30,000 – 55,000 cPs
    *Flash Point ASTM D 93 >135°C
    *Pot life (300g mix) @ 30°C – 30m @ 28⁰C
    *Gel time (18g mix) @ 30°C – 2h @ 28⁰C
    *Hardening time – 24 hours
    *Full Cure – 7 days
    *Flexural Strength ASTM D 790 66.9 MPa
    *Flexural Strength ASTM D 695 65.4 MPa
    *Compressive Strength – Ultimate ASTM D 695 116.2 MPa

    These are typical results under laboratory conditions.

    NOTE

    At 40°C gel time will be reduced to half, in case of increased temperatures, pouring should be planned accordingly.

    GENERAL INFORMATION

    Substrate preparation: The substrate of the substrate must be clean and dry. Remove all dirt, grease and foreign material by cleaning with suitable solvent, sand blasting, mechanical abrasion, or acid etching.

    Mixing: To obtain good results, thorough mixing of the ingredients is essential. Usually the resin and hardener are mixed in small quantities to extend the working time and prevent high exothermic reaction and pre-gelling.

    Application: To ensure good adhesion between the substrates, it is recommended to apply rich layer of homogenous blend uniformly on the surface and fill the dents and pinholes. Adequate cuing normally takes place within 24 hours, post curing at temperatures more than 40°C is recommended.

    Cleaning and maintenance of equipment: Tools and equipment used during the process are best cleaned immediately after use since removal of cured resin is difficult and time consuming. It is recommended that the bulk of the resin be removed using a scrapper and the remainder washed away using solvents such as toluene, xylene or acetone.

    PAKAGING

    Zepoxy 200 is available as follows:

    Mini set                         180g                          Part A: 100g
    Part B: 80g

    Half Set                          900g                         Part A: 500g
    Part B: 400g

    Full Set                          1.8 KG                        P art A 1 KG
    Part B: 800g

    Commercial Pack         54 KG                         Part A: 30 KG                                                                                                                            Part B: 24 KG

    HEALTH AND SAFETY

    Dispose containers of the materials as per local laws, rules, and regulations. Use gloves, safety masks and other safety apparel as per health and safety laws. For further assistance, please refer to the MSDS of the product for further health and safety information.

    Packaging

    Mini Set 180g, Half Set 900g, Full Set 1.8 KG, Commercial Pack 54 KG
Technical Datasheet
Product Description
Zepoxy Tabletop Deep Pour is a retarded clear epoxy casting system, which offers a long open time for precise article placement and complete bubble removal. It has inbuilt UV inhibitors as well as excellent visual properties. It also avoids high exothermic reaction and the resulting shrinkage after curing.
Zepoxy 200 is an all-purpose epoxy adhesive useful for bonding of materials such as metal, wood, ceramic, FRP, concrete, textile, glass, leather, etc. It has higher bonding power as well as higher mechanical strength making this system a higher performance version of Zepoxy 100.

TECHNICAL DATA

Property Test Method Result
Appearance Part A Visual High viscosity, translucent liquid
Appearance Part B Visual High viscosity, yellow to brown liquid
Mix ratio (Part A: Part B) Theoretical 100: 80
*Mix viscosity @ 25°C ASTM D 2196 30,000 – 55,000 cPs
*Flash Point ASTM D 93 >135°C
*Pot life (300g mix) @ 30°C - 30m @ 28⁰C
*Gel time (18g mix) @ 30°C - 2h @ 28⁰C
*Hardening time - 24 hours
*Full Cure - 7 days
*Flexural Strength ASTM D 790 66.9 MPa
*Flexural Strength ASTM D 695 65.4 MPa
*Compressive Strength – Ultimate ASTM D 695 116.2 MPa
These are typical results under laboratory conditions.

NOTE

At 40°C gel time will be reduced to half, in case of increased temperatures, pouring should be planned accordingly.

GENERAL INFORMATION

Substrate preparation: The substrate of the substrate must be clean and dry. Remove all dirt, grease and foreign material by cleaning with suitable solvent, sand blasting, mechanical abrasion, or acid etching. Mixing: To obtain good results, thorough mixing of the ingredients is essential. Usually the resin and hardener are mixed in small quantities to extend the working time and prevent high exothermic reaction and pre-gelling. Application: To ensure good adhesion between the substrates, it is recommended to apply rich layer of homogenous blend uniformly on the surface and fill the dents and pinholes. Adequate cuing normally takes place within 24 hours, post curing at temperatures more than 40°C is recommended. Cleaning and maintenance of equipment: Tools and equipment used during the process are best cleaned immediately after use since removal of cured resin is difficult and time consuming. It is recommended that the bulk of the resin be removed using a scrapper and the remainder washed away using solvents such as toluene, xylene or acetone.

PAKAGING

Zepoxy 200 is available as follows: Mini set                         180g                          Part A: 100g Part B: 80g Half Set                          900g                         Part A: 500g Part B: 400g Full Set                          1.8 KG                        P art A 1 KG Part B: 800g Commercial Pack         54 KG                         Part A: 30 KG                                                                                                                            Part B: 24 KG

HEALTH AND SAFETY

Dispose containers of the materials as per local laws, rules, and regulations. Use gloves, safety masks and other safety apparel as per health and safety laws. For further assistance, please refer to the MSDS of the product for further health and safety information.